1.5 Interfacing Basics

This configuration can be used either as a simplex repeater or as an announcement machine, since it is not necessary in either of those modes to transmit and receive simultaneously. The three connections should be made as follows: Transceiver to Sound Card Receive Audio This is usually a simple matter of running a shielded audio cable from the radio’s speaker jack or “line out” jack to the Line In connector on the sound card. If you are unsure which connector on the sound card is Line In, consult the documentation that came with the sound card. In some cases, the Line Out or Rec Out signal from the radio is not strong enough to be used with the sound card’s Line In connector. The Microphone In connector can usually be used instead. In either case, be sure the sound card software’s Recording control is set up to receive audio on the connector being used. Sound Card to Transceiver Transmit Audio If the transceiver has a Line In connector, a shielded audio cable can be run directly from the sound card’s Line Out connector to the radio’s Line In connector. Otherwise, it is necessary to connect to the radio’s microphone connector using an attenuating cable, or a cable with an attenuator connected. This prevents the radio’s microphone circuit from becoming over-driven.

Connecting a Transceiver

E-Mail This page describes some of the settings that have been used successfully with a few of the applications that I use on a regular basis, and hopefully, will provide at least some guidance to others as they struggle with this and that to try to make everything play as they are hoping. Here’s the run-down on my very modest station: HP Pavillion Slimline, s , with dual monitors Interface: I just haven’t put it away yet.

Apr 21,  · 1) Your duplexer between the 2m/ radio and the two antennas. Just how is a duplexer work? Is it like a passive speaker crossover? 2) How can these VHF/UHF antennas hook up to .

Password Rig Interface Help The following is the essential information you’ll need to get your rig interface connected, up and running with AC Log and my contesting software. To get started with rig interface, you’ll need the necessary interface hardware to connect your rig to your PC. You’ll find a variety of W1GEE interfaces that support most of the common rigs here! To interface your rig with my software, once you have the necessary hardware connected between your radio and PC, configure the rig interface form as follows: For Select Rig, select the rig you are interfacing.

For most rigs, simply selecting the correct rig will also accurately set your baud rate, parity, data bits, stop bits and polling string! If you select Icom, you will also see text appear, asking you to change the rig ID 64 by default, which happens to be for the Pro II to the ID for your rig the red lines in the graphic above. If there is a small h, such as 64h, ignore it and just enter the two digit number.

I’ve also included all the successful settings I’ve received from other users below, which include the rig ID. For Com Port, select the com port that you have your rig connected to. Even if only one port is listed, you still have to click on the port to select it. For Connection Power, select the power option, if any, that your interface requires. If you have entered your settings correctly, you should be all set to enable rig interface.

Beginners’ Guide to Fldigi

It has gotten a thorough workout and I have not had any issues with it at all. So it is a good investment to be able to do all of these functions and only have one set up cables and interfaces that you are working with. I would recommend the RIGblaster Pro to anyone. RIGblaster Pro Features Can be used with almost any make or model microphone and most model radios no matter what brand Any radio that has a 8 pin round screw on microphone connector Any radio that has an Rj45 modular telephone style connector Any radio with Rj25 6 wire microphone connector with the purchase of an optional Ft style 6 wire modular mic.

This jack is for use with non-sound card software using serial DTR control.

The following is the essential information you’ll need to get your rig interface connected, up and running with AC Log and my contesting software. To get started with rig interface, you’ll need the necessary interface hardware to connect your rig to your PC.

All trademarks are the property of their respective owners. We hope that it provides many hours of amateur radio enjoyment. Page 3 able to transmit! If you have a problem with this step simply install and try another similar ham radio program instead. If another program works you can be sure you there was a problem with the first program. If several programs do not work then double check your sound card virtual settings and your audio connections.

This is only a sample station hookup diagram; what might be used for portable operation with a RIGblaster nomic. A desktop computer would have similar connections with different sound card connections. If possible one you will keep it in.

Block diagram of my Amateur Station

IC , Rigblaster, and fldigi Click for larger version with detailed notes on components Hams have known for a century how much fun it is to use narrowband digital communications to punch through atmospheric conditions and make a little power communicate over very long distances, sometimes literally around the world. One of the fun ways to do this today, especially for newly minted hams without International Morse code skills, is to use a computer to modulate the signal and do the decoding for you.

One of the best programs out there for computer modulation is fldigi. It is free, open source software. Ultimately it does a lot of what Internet chat does, but you can do it on battery power, and without an Internet, or wires. Fldigi visualizes the signals across the audio frequency space over time using a colorful waterfall display.

Rigblaster Plus with Elecraft K3. Did someone have the Rigblaster Plus with an elecraft K3? I want to operate FSK in Data Mode and I want to know if someone has the setting. I have the mm stereo.

Proven performance, over 15 Thousand on-the-air! Compatible with almost every radio and every sound card equipped computer. Properly matched audio to any radio. Easily adjustable to any radio’s mic. Fully isolated computer ground circuit using optoisolators, unlike other interfaces that require extra ground screws, extra wires and extra cables in an attempt to eliminate ground loops. Easier hookup thanks to our fully isolated audio and computer keying circuits.

Far and away the easiest to use, most complete and up to date CD, included for free. Positive and fully automatic PTT control supported almost ham programs, no illegal or spurious signals. Stainless steel and black anodized stainless steel hardware. Commercial quality mini toggle switches; no cheap slide or push switches. The only interface that has quick change mic. No wires sticking through holes to get frayed and break loose.

West Mountain Radio

Uncategorized Flex and Setup These are the settings I am using with my original Flex and now upgraded to running on Microsoft Windows 7 on an Apple Mac Mini using the Bootcamp partition. I will try to keep this document up to date as I make changes. I initially configured it as recommended in the Flex installation instructions. Flex Flex After installation I only did minimal configuration, set buffer size and sample rate and would do the rest later.

Flex and Setup These are the settings I am using with my original Flex and now upgraded to running on Microsoft Windows 7 on an Apple Mac Mini using the Bootcamp partition. I will try to keep this document up to date as I make changes.

Ham Radio Deluxe Getting Started Before you can use Ham Radio Deluxe to control your transceiver, you need to give due consideration as to how it was designed to interface with the computer and this can be confusing for newcomers. The main program sends coded control commands to the transceiver and receives information back from it. Only commands provided by the transceiver manufacturer are available for the program to use.

If you want to use PSK31 Deluxe as well, two audio connections are also required. Received audio from the transceiver needs to be routed to the soundcard and transmit audio from the soundcard needs to be routed to the transceiver. Most rigs these days will have special inputs and outputs for these functions. Read your manual to find out how it should be done. Additional explanation can be found by downloading the Interfaces.

The most common types of connection are: RS cable between the computer and the transceiver – with or without a level converter. There are a number of variations on the RS connection. The variations will generally be in whether a level converter is necessary and whether a straight through or NULL Modem or crossover cable is required. For example, the manual for the Yaesu VR receiver specifies the crossover type of cable for cloning copying the digital setup of one unit to another identical unit and the straight through cable for receiver control.

If it’s not right, it won’t work.

Flex 3000 and 5000 Setup

With the advent of high speed computing and digital signal processing DSP all this has changed. If you own a home computer PC with a sound card, all you need to do is download software and obtain an interface between the PC and your radio. The interface provides the audio and digital signal level translation between the computer and the radio. Due to lack of locally available interfaces many hams imported them for large sums of money.

Icom IC Frequently Asked Questions (FAQ) Icom IC Frequently Asked Questions (FAQ) This guide was created to answer the most commonly asked questions about the Icom IC

Just how is a duplexer work? Is it like a passive speaker crossover? You are using the Cushcraft R and an antenna tuner. Does this work out well; or is it a compromise? How come you you don’t use the dipole for the CB too? Or won’t it tune up on 11 meters. I’ve always wondered about that one. Don’t like them – or? And you have two sets of audio cables between the Ham rig and the CAT. I don’t know squat about digital modes but I am considering the Rigblaster Pug ‘n Play.

Too little or just not good enough? It’s alittle confusing at this point, as I have a computer and want to be able to hook it all up. Isn’t the Icom efficient enough – or does it fall on its own face?

Ham Radio Deluxe

Setting up the computer sound card There are many devices that can do this operation. This is by far one of the least expensive and smallest packages on the market. The RIGblaster nomic draws its power through the serial port from the computer which eliminates a power cable.

Speed: The CAT Rate you set up for Menu 31 in Step 1a above. e. Flow Control: RTS f. On the FT Set the FT Mode to Data-USB and set the Width on the touchscreen to Hz. K9EQ-FUSION-PDF_HRD-FT Rev. 2 2-Oct Page 3 of 8 8.

Each of these tabs is described in detail below. EchoLink needs to be able to detect when a signal is being received at the receiver. Normally, a built-in VOX system monitors the received audio and triggers EchoLink when it rises above a certain level. However, for more positive operation on simplex links, it is also possible to connect the carrier-detect signal directly from the receiver to one of the PC’s serial ports. Select this option if you do not wish to use VOX or the serial port. In order to “transmit” to the other station over the Internet, you must click the Transmit icon or press the space bar.

This would normally only be selected for testing. Select this option if you do not have a carrier-detect connection between your receiver or transceiver and your PC’s serial port. This is the default. When VOX is enabled, and a connection is established to a remote station, EchoLink will begin “transmitting” to the remote station whenever the peak audio level rises above the VOX threshold.

The VOX threshold is set using a slider that appears just below the audio level indicator at the bottom of the EchoLink screen. When the VOX has been triggered by a local signal, EchoLink will continue sending audio to the station on the Internet for a short amount of time after the signal stops. VOX Delay controls this time period, in milliseconds.

Increase this number if local stations tend to leave silent pauses frequently in their transmissions.

Going Digital Video Tutorial